Zenitco KV-4/2U Remote Pressure Switch (Dual)
- $179.00
-
Zenitco KV-4/2U Remote Pressure Switch (Dual)
Genuine Zenitco | Dual remote switch for running a Klesch-2 flashlight and Perst-4 aiming module together
In short: the Zenitco KV-4/2U is a dual remote switch that drives a Zenitco Klesch-2 flashlight and an updated Perst-4 aiming module at the same time from one Picatinny-mounted pad.
Overview
The KV-4/2U lets you run two devices - a Klesch-2 flashlight and a Perst-4 aiming module - from a single remote pad, so you don't need two separate buttons on the rail.
It plugs into both devices and clamps to any Picatinny (1913) rail with captive set screws. The U version is for the updated Perst-4; for the earlier Perst-4 the KV-4/2 is the matching switch.
What's in the Box
| ✓KV-4/2U Dual Remote Pressure Switch | x 1 |
| ✓User Manual | x 1 |
Key Advantages
- Runs two devices - Klesch-2 flashlight and Perst-4 aiming module from one pad
- For the updated Perst-4
- Clamps to any Picatinny (1913) rail
- Genuine Zenitco part
Technical Specifications
| Brand | Zenitco |
| Type | Dual remote pressure switch |
| Mounting | Picatinny (1913) |
| Fits | Zenitco Klesch-2 flashlight and updated Perst-4 aiming module |
| Warranty | Manufacturer warranty (storage and service life): 60 months |
| MPN | Zen-KV-4/2U |
| Condition | New |
Frequently Asked Questions
What does the KV-4/2U do?
It is a dual remote switch that fires a Zenitco Klesch-2 flashlight and an updated Perst-4 aiming module at the same time from one pad.
How does it mount?
It clamps onto a standard Picatinny (1913) rail with captive set screws and plugs into both devices.
KV-4/2 or KV-4/2U?
The KV-4/2U is for the updated Perst-4; the KV-4/2 is for the earlier Perst-4. The updated Perst-4 carries an engraving under the button connector. If unsure, send us your Perst model.
What does the KV-4/2U control?
It drives two devices from one pad - a Klesch-2 light and a Perst-4 aiming module, in their older versions. Both plug into the switch, and each has its own button.
How does it mount?
Back the two set screws out, place the switch anywhere on a Picatinny rail, then tighten the screws down. The cable plugs into the tailcap of the device it controls.
Is this a genuine Zenitco part?
Yes - an original Zenitco part with guaranteed US delivery.
Genuine Zenitco KV-4/2U - ready to ship.
In Stock | Guaranteed US Delivery | Genuine Zenitco Part
In Stock | Guaranteed US Delivery | Genuine Zenitco Part
Compatibility Note: Mounts on a Picatinny section or a handguard surface, with the cable routed to the device and held by an FP-series wire holder. Check your connector generation before ordering - early and updated connectors differ.
Genuine Zenitco part, shipped from the USA.
In Stock | Guaranteed US Delivery | Genuine Zenitco Part
In Stock | Guaranteed US Delivery | Genuine Zenitco Part
General
Mounting
Picatinny (1913)
Type
Dual remote pressure switch
Brand
Zenitco
Manufacturer Part Number (MPN)
Zen-KV-4/2U
Condition
New
Intended Use
Zenitco Klesch-2 flashlight and updated Perst-4 aiming module
Mounting & Rails
Mounting
Picatinny (1913)
Function
Dual remote pressure switch
